The image shown is the 200W FM transmitter MPX or Stereo versions with the digital frequency display, product codes 200wplld19p and 200wpllsd19p in the price list below.
This is the lowest cost of all the versions available, but is not intended for the novice or beginners, in fact this unit is for stations with more engineering experience. The audio input to this is a direct raw MPX signal and does not include any audio limiting or stereo coder circuitry, this must be provided externally in accordance with the recommendations of http://www.aareff.com/ETR132.pdf.
FM Transmitter Stereo Version - This is similar to the Mono/MPX version except it is stereo and RDS cannot be used with this. Again stations with more engineering experience may use this version, this is because it does not include audio limiting. Again the audio limiting for this version must be externally provided and in accordance with the recommendations of http://www.aareff.com/ETR132.pdf. This version is typically used with external multi band processors and stereo generators such as the brands Orban or Inovonics. Not recommended for novice stations or beginners.
Stereo and Audio Processing
FM Transmitter Stereo Version with Audio Compression and Limiting - Most small radio stations and beginners will use this version, this is because it includes audio processing circuitry and suitable limiting to keep the transmitter in compliance with the maximum bandwidth permitted by the international regulations. There is also access to the MPX in and out on the back panel which allows all known RDS units to be connected. Novice stations with limited experience of FM broadcasting transmitters should purchase this version.
Do You Have Any Questions? Please Message Us Here ...
This transmitter produces 200 watts of transmitter power and will operate with ease at full power 24 hours a day non stop in any country and with any AC voltage in the world. The unit has a neat little meter on the front panel lit up with intense blue LED's to indicate forward and reflected power. The RF output power of the amplifier automatically folds back to a safe level when there is fault condition of poor SWR and return loss of any level for any duration of time. When the fault clears the amplifier restores to full power.
Made To Last !
Over the last 12 years in Africa and Middle East alone we sold our systems into Congo, Uganda, Liberia, Zambia, Yemen, Rep South Africa, Oman, United Arab Emirates, Tanzania, Southern Sudan, Kenya, Ghana, Gambia, Nigeria and Niger. Our transmitters are very popular in very hot climates as they handle the heat and the dust very well under 24/7 operation.
|Version||MPX||Stereo||Stereo and Audio Processor|
|Signal To Noise Ratio||80dB||65dB||65dB|
|Audio Distortion||0.02% THD Max.||0.02% THD Max.||0.02% THD Max (at MPX section).|
RF Technical Specification
|Audio Input Sensitivity||+4dBu for +/- 75KHz dev.|
|Freq Stability||+/- 1KHz max. typ. +/-300Hz|
|Deviation Sensitivity Stability||+/-2% max|
|Freq Fine Adj||> +/- 1000Hz|
|Pre-emphasis||(50uS/ 75uS/ None) Selectable|
|Audio Input Connector||Phono/ RCA type unbalanced sockets|
|Power Output||Adj. 20-200 Watts into 50 ohms|
|Freq Range||87.5 to 108MHz|
|Spurious Emissions||Less than -75dB ref to carrier|
|Harmonic Emissions||Less than -70dB ref to carrier|
|Residual AM||Less than 0.5%|
|Synchronous AM||Less than 0.5%|
|RF Ruggedness||Any VSWR phase or length of time|
|Output Connector||SO239 (or optional N type)|
|Input Connector||BNC 50 ohms|
|Operating Temp||-20 to +40 Deg C|
AC Technical Specification
|Input Voltage||90 to 260 VAC 47-63 Hz 124 to 370 VDC|
|Input Power||380-420W for 200W RF OUT with RF SWR < 1.5|
|Power Factor||PF>0.95/230VAC PF>0.98/115VAC at full load|
|Working Humidity||20 ~ 90% RH non-condensing|
|Safety Standards||UL60950-1 TUV EN60950-1 Approved|
|EMC Conduction & Radiation||Compliance to EN55022 (CISPR22) Class B|
|EMC Harmonic Current||Compliance to EN61000-3-2 -3|
|EMC Immunity||Compliance to EN61000-4-2 3 4 5 6 8 11; ENV50204 Light industry level criteria A|
All these models comply with European standards ETS 300384 for R&TTE, EN 301 489-11 for EMC and (LVD) 2006/95/EC for safety and ITU-R BS.450-3 (11/01) FM Broadcasting at VHF